Sale
ChiTu L V3 board for mono screen mSLA/LCD 3d printer
$42.98 – $72.98
ChiTu L V3 supports 6.08inch and 5.96inch MONO and 5.5inch RGB LCD screen.
Also bought together
- Description
- Reviews (17)
- Additional information
- Tracking
Description
SLA Controller Board ChiTu L 5.5 V3 For Creality LD-002R Printer With 32Bit ChiTu System For LCD 3D Printer Motherboard
The firmware option is FPGA firmware come with board, you can also update yourself from our download page.
Parameters:
Mainboard size：120*85mm
Microprocessors：STM32F407(168Hz)
Input voltage:12~24V 5~15A
Motor driver：Allegro A4988(2 extended signal)
Color touch screen：2.8/3.5/4.3/5.0 inch TFT color touch screen
Supported LCD screen：5.5inch /6.08inch monochrome 2k
Data interface:U disk,Network port,WIFI
Supported file format: ctb
Interface type：MIPI
Slice software：CHITUBOX
Shipping list：
1.only board： controller board + gifts
2. controller board + 2.8/3.5/4.3/5.0 touch screen + 50cm FFC cable + gifts
Notice:
The touch screen can only be used for ChiTu controller board.Other screens may not match ChiTu controller board.
ChiTuL5.5 V3 is our major board for small size monochrome LCD, it supports different version of
*Support DXQ 6.08inch monochrome LCD resin panel 1620*2560(ZX608XI5249727/DXQ608-X04)
*Support Duobond 5.96inch monochrome LCD resin panel 1620*2560（RV059FBB-N80）
Chitusystems compatibility chart
| Screen | Interface | V1 | V2 | V3 | K1 | H1 |
| 5.5‘’-RGB-1440*2560 | MIPI/03 | ● | ||||
| 5.5‘’-RGB-1440*2560 | MIPI/04 | ● | ● | ● | ||
| 5.5‘’-RGB-2160*3840 | MIPI | ● | ||||
| 5.5‘’-MONO-1080*1920 | MIPI | ● | ● | ● | ||
| 5.96‘’-MONO-1620*2560 | MIPI | ● | ● | |||
| 6.0‘’-RGB-1440*2560 | MIPI | ● | ||||
| 6.08‘’-MONO-1620*2560 | MIPI/04 | ● | ● | |||
| 6.23‘’-MONO-3840*2400 | MIPI | ● | ● | |||
| 8.9‘’-RGB-2560*1600 | MIPI | ● | ||||
| 10.1‘’-RGB-2560*1600 | MIPI | ● | ||||
| 12.5‘’-RGB-3840*2160 | eDP | ● | ||||
| 13.3‘’-RGB-3840*2160 | eDP | ● | ||||
| 15.6‘’-RGB-3840*2160 | eDP | ● |
Notice
Installing power supply：
As shown below, connect the power supply wire with -12V/24V+ port.
Please note: reverse connection of the positive and negative poles will make damage to the motherboard !!!
You can also Click here to find out the difference between Mono LCD and RGB LCD.
17 reviews for ChiTu L V3 board for mono screen mSLA/LCD 3d printer
Powered by Customer Reviews plugin
Showing 17 of 17 reviews (5 star). See all 17 reviews
Additional information
| Weight | 0.7 kg |
|---|---|
| Firmware Option | |
| Touch screen Size | 2.8 inch, 3.5 inch, 4.3inch, 5.0 inch, only board |
Ellie Julius –
Works! Came with a problem with the MIPI connector. But if it is pressed, then the signal on the LCD goes. The service works clearly!
Tandy Hoyte –
Xose Mendez –
Finn Junkermann –
Germain Beaumont –